- Products
- Compressors & Assemblies
- Compressors
- Semi-hermetic
- Reciprocating piston
- Bitzer semi-hermetic compressor BE5 4HE-18Y-40P 400V
Bitzer semi-hermetic compressor BE5 4HE-18Y-40P 400V
More in this category: Reciprocating piston
One click to the most important information:
Description
A closely stepped range of compressors for modern refrigeration, air conditioning and heat pump systems.
With its new BITZER ECOLINE series, BITZER offers high-efficiency universal compressors that satisfy the demands of modern refrigeration systems:
- extended range of applications
- energy ...
A closely stepped range of compressors for modern refrigeration, air conditioning and heat pump systems.
With its new BITZER ECOLINE series, BITZER offers high-efficiency universal compressors that satisfy the demands of modern refrigeration systems:
- extended range of applications
- energy efficient
- cost-effective power regulation
- wear-resistant drive mechanism
- quiet and low-vibration
- minimal space requirements
- robust
BITZER ECOLINE compressors for operation with frequency inverters up to 70 Hz
All BITZER ECOLINE compressors are designed and optimised for 70 Hz operation. Depending on the refrigerant used and the environmental conditions, a compressor with a PW standard motor (400 V, 3-50 Hz) can be used, or a special motor (230V/400V, 3-50 Hz*) may be required and connected in a delta circuit (230 V, 3-50 Hz). The latter is the case for compressors using version 1 and 2 motors where they are to be operated throughout the entire documented area.
The use of a PW standard motor for 400 V or the connection of a 230/400 V motor in a star circuit must be discussed with BITZER on an individual basis due to the drop in the torque value when operating above 50 Hz (fig 1) – see also Technical Information KT-420.
* Compressors 2KES-05Y to 4BES-9Y are fitted with 230/400 V, 3-50 Hz motors as standard and can be operated in either a 400 V star circuit configuration or at 230 V in a delta circuit.
Accessories / Replacement parts
-
Additional ventilator
-
Check valve
-
Control valve for power controller
-
Control valve for unloaded start system
-
Crankcase heater
-
Electronic oil pressure safety switch
-
IQ Module add-on
-
Injector valve
-
Insulation cover for motor
-
Motor protection
-
Oil equalisation connection
-
Oil pressure safety switch
-
Oil servicing valve
-
Option: Refrigerator oil BSE55 with R134a, tc > 70 °C
-
Power controller
-
Pressure transducer
-
Pressurised gas temperature sensor
-
RSK unit (Liquid receiver without compressor)
-
Rail set top
-
Refrigerant collector for RU
-
Refrigerator oil
-
Unloaded start system
Technical data
Notes
- Data for 400 V/3/50 Hz with direct mains power supply. Observe the max. operation current / max. power input when selecting contactors, leads and fuses. Contactors: Category AC3. Use overcurrent relay to avoid exceeding max. operating current.
PW: Part winding motor Y/YY
- 4VES-6Y .. 6FE-50Y wind distribution 50%/50%
- 8GE-50Y .. 8FE-70Y Δ/ΔΔ wind distribution 60%/40%
- Use motor contactors rated to about 60% of the max. operating current for PW start up.
- Y/Δ design on request
380-420V PW YY-3Ph-50Hz
440-480V PW YY-3Ph-60Hz
Data for integration of the frequency converter (FC) – motor version 3 (R134a compressor): based on 400 V/3/50 Hz mains supply and use of 400 V/3/50 standard motor for FC operation up to 70 Hz. FC motor versions 1 and 2: Operation above 50 Hz anywhere within the operating area requires a special voltage motor.